Re: [CR]Field Expedient Front Center Pull Cable Stop

(Example: Component Manufacturers:Chater-Lea)

From: Renaissance Cycles <info@renaissance-cycles.com>
To: "heddarr" <heddarr@indianaconnect.com>, "Thomas R. Adams, Jr." <kctommy@msn.com>, <classicrendezvous@bikelist.org>
References: <BAY4-F2506IBPGJTE4D0000f677@hotmail.com> <002501c33dd8$e70e2500$7a549e8d@clymeralliance>
Subject: Re: [CR]Field Expedient Front Center Pull Cable Stop
Date: Sun, 29 Jun 2003 12:58:59 +0200


Thomas:

There's also diagrams of this process provided with Zeus brakesets so to say it's not a backyard process..........If I find an extra one I'll send it off to you.

BTW: Not to start a long debate of whether Mafacs are good stoppers or not because I can see it coming!............

With a little finess Mafacs are good stoppers.

BC
Baron C...................And the gang!!
Renaissance cycles,
Eindhoven Holland.


----- Original Message -----
From: heddarr
To: "Thomas R. Adams, Jr."


<classicrendezvous@bikelist.org> Sent: Sunday, June 29, 2003 2:53 AM Subject: Re: [CR]Field Expedient Front Center Pull Cable Stop


> Warmest greetings
>
> I drilled an SR stem in the early 80's. I drilled through the stem with a
> bit just large enough for the cable to pass through. Then picked a bit just
> a bit larger than the cable with a ferrell (SP). I drilled it 3/8" deep. I
> located the first hole by sighting the entrance and exit of the hole in the
> stem so that the brake cable was parallel to the head tube.
>
> Not broken yet with many miles on it. By the by I am not a willowy
> lightweight.
>
> I have seen drilled GB stems in the Ron Kitching catalog and I bet there are
> some list members who have one floating around.
>
> There are also some brake hangers that clamped on. Do not know if they are
> still available.
>
> One of the first modifications I did to a bike with a Mafac hanger was to
> replace it with a Weinmann one. I gained an adjusting screw and it was much
> stiffer.
>
> Have Universal 68 and NR brakes but if I want to stop I use Weinmann,
> Universal and Zeus centerpulls.
>
> Howard Darr
> Clymer PA
> ----- Original Message -----
> From: "Thomas R. Adams, Jr." <kctommy@msn.com>
> To: <classicrendezvous@bikelist.org>
> Sent: Saturday, June 28, 2003 7:58 PM
> Subject: [CR]Field Expedient Front Center Pull Cable Stop
>
>
> > For various reasons, I want to use a set of center pull brakes (Mafac
> Racers) on a frame that has a Campy NR headset installed and no room for a
> normal Centerpull housing stop in the headset. The fork appears to be
> trimmed too short (threads on the lock nut only 2/3 engaged and no spacers
> in the headset) to accomodate even the thin Mafac hanger. I can replace the
> headset with a lower stack headset like a Ritchey that would leave room for
> the hanger, but that option doesn't really appeal to me. I'd like to keep
> the appearance fairly traditional and early 60's. Hence the Mafacs and
> Campy headset.
> >
> >
> >
> > What options are there for obtaining a hanger on this bike? Can I put the
> hanger on top of the lock nut, and attach it to the nut? Could you remove
> it later?
> >
> >
> >
> > Can I grind down one of the headset components to make the room? (least
> favored option as it degrades the condition of the headset).
> >
> >
> >
> > Or should I drill a cable route/stop through the stem? The stem is a
> Nitto Technomics with a 9cm extension. Would a drilled Nitto stem be safe?
> How big do you make the top and bottom holes? How far out on the extension
> do you drill?
> >
> >
> >
> > Or does someone have a better idea?
> >
> >
> >
> > Okay guys, get creative.
> >
> >
> >
> >
> >
> > Tom Adams, Shrewsbury NJ
> >
> >
> >
> > ------------------------------------------
> > MSN 8 helps
> > ------------------------------------------
> > ELIMINATE E-MAIL VIRUSES.
> > ------------------------------------------
> > Get 2 months FREE*.