Re: [CR] proper insertion and mounting techniques (for tires and tubes, that is)

(Example: Production Builders:Peugeot:PX-10LE)

In-Reply-To: <mailman.4619.1257259479.72377.classicrendezvous@bikelist.org>
References:
From: "Jon Spangler" <jonswriter@att.net>
Date: Tue, 3 Nov 2009 19:12:22 -0800
To: <classicrendezvous@bikelist.org>
Subject: Re: [CR] proper insertion and mounting techniques (for tires and tubes, that is)


Harvey and Bob,

It is nice to know that the two of you can "go at it" for a few "rounds" of proper tire technique and

"still respect (each other) in the morning. Really."

And, regardless of which technique(s) one uses, proper inflation counts, too. (But let's not get too "pumped up" about that, shall we?)

Once the ultimate inflation is reached, proper pressure is assured, and the wheel has been returned to its proper position in the frame, don't forget the ultimate rule of tire changing:

Keep the rubber side down." :-)

Jon Spangler who usually uses the Bob Freitas-endorsed technique but who deeply appreciates Harvey Sachs' East Coast methods of tire-marking, tire-centering, and flat- locating in Alameda, CA USA

On Nov 3, 2009, at 6:44 AM, <classicrendezvous-request@bikelist.org> <classicrendezvous-request@bikelist.org> wrote:
>
> Message: 7
> Date: Tue, 3 Nov 2009 07:17:17 -0500
> From: Harvey Sachs <hmsachs@verizon.net>
> Subject: [CR] Harvey on Re: Harveys tire mounting tricks
> To: <freitas1@pacbell.net>, Classic Rendezvous
> <classicrendezvous@bikelist.org>
> Message-ID: <4AF01F4D.2000509@verizon.net>
> Content-Type: text/plain; charset="us-ascii"; format=flowed
>
> Bob Freitas wrote:
>
> I think Harvey failed to explain the tire mounting procedure
> correctly (but I am sure he does it correctly)
> With one bead of the tire on the rim insert the tube (I put a small
> amount of air in it so it is not flat) then starting AT THE VALVE push
> the valve in (you want the round base of the tube up inside the
> tire)and
> begin installing the other side(bead) of the tire. This way the valve
> ends up straight , you install away from the valve on both sides
> moving
> towards the other side of the wheel.
> So repeating you start AT THE VALVE and work away on both sides
> My Dad showed me this is 1963 or so. Back then we did mainly
> tubes with
> rubber stems (Schrader)
> +++++++++++++++++++++++++++++++++++++++++++++++++
> Well, Bob, thanks, and it seems that I repeated Michelin's
> instructions
> clearly enough to provoke disagreement. Michelin and I (one of whom is
> an authority almost equal to your father? :-) ) seat the tube and the
> valve stem, but then start working the second bead from the point
> opposite the valve hole. As I said originally, that allows pushing as
> much of the bead as possible down into the well of the rim, so the
> tire
> mounts easily. Nope, I didn't believe at first, so I tried it. And
> have
> been doing it that way ever since. Since I work both sides onto the
> rim
> equally, it magically turns out that the valve stem winds up nice and
> perpendicular, almost every time.
>
> Only advantage of the Michelin route is that it's easier to get the
> bead
> over the rim, since it's easier to push more of the bead down into the
> well of the rim.
>
> But, your mileage may vary. And I'll still respect you in the morning.
> Really.
>
> harvey sachs
> mcLean va
>

Jon Spangler Writer/editor Linda Hudson Writing

PLEASE NOTE NEW CONTACT INFO
TEL 510-864-2144
CEL 510-846-5356
JonSwriter@att.net
http://www.linkedin.com/in/jonmspangler
http://www.twitter.com/jonmspangler