Re: [CR] Hi-E Nipple AND Spokes??????

(Example: Framebuilding:Brazing Technique)

Date: Thu, 12 Nov 2009 16:24:42 -0700
From: <mrrabbit@mrrabbit.net>
To: hfbirm <hfbirm@bellsouth.net>
References: <329419.86674.qm@web82201.mail.mud.yahoo.com> <1257984887.4afb5377b3317@www.mrrabbit.net> <397707.97592.qm@web180302.mail.gq1.yahoo.com>
In-Reply-To: <397707.97592.qm@web180302.mail.gq1.yahoo.com>
Cc: Jerome & Elizabeth Moos <jerrymoos@sbcglobal.net>, classicrendezvous@bikelist.org
Subject: Re: [CR] Hi-E Nipple AND Spokes??????


It does seem odd...but that's what the French used - 63.5 TPI.

The other odd TPI is the one used for 120 spokes - it is not the same as 105s.

If I remember correctly - 120s use fewer TPI.

=8-)

In the meantime...what's Jerome gonna do!

=8-)

Robert Shackelford San Jose, CA USA

Quoting hfbirm <hfbirm@bellsouth.net>:
> 63.5tpi ?  You're really going to have everyone questioning the French.  :)
> That's 2.5 tp mm, which makes much better sense to this Yank.
>
> Jim Carter "I think the French metric sizing system was correct" in
> Bham, AL
>
>
>  
>
>
>
> ________________________________
> From: "mrrabbit@mrrabbit.net" <mrrabbit@mrrabbit.net>
> To: Jerome & Elizabeth Moos <jerrymoos@sbcglobal.net>
> Cc: classicrendezvous@bikelist.org
> Sent: Wed, November 11, 2009 6:14:47 PM
> Subject: Re: [CR] Hi-E Nipple AND Spokes??????
>
> Wow!
>
> You may have yourself in quite a bind here...
>
> I'm guessing you might have 63.5 TPI (French) or the TPI common to 120 spokes
> -
>
> the larger cousing to 105 spokes.  Where to get 15g spokes with Hi-E
> threading...me totally clueless.
>
> Would standard nipples work?  Might have to go that route unless someone else
>
> here comes to the rescue.
>
> =8-(
>
> (Been ages since I've worked on anything other than 56 TPI)
>
>
> Robert Shackelford
> San Jose, CA USA
>
> Quoting Jerome & Elizabeth Moos <jerrymoos@sbcglobal.net>:
>
> > Well, in my continuing Hi-E Project, having destroyed one rim trying to
> true
> > a Hi-E wheel with old corroded spokes, I decided to respoke, but hoped to
> > reuse the special Hi-E nipples.  The original spokes measure 15 ga on the
> > end, so I ordered some 15 ga DTs to rebuild with.  But when they arrived
> > today, I found I cannot thread the Hi-E nipples more than a couple of turns
> > onto the DT 15 ga spokes.  Did Hi-E make their own spokes as well as
> nipples?
> > Did they use a non-standard thread?
> >
> > Regards,
> >
> > Jerry Moos
> >
> >
> >
> > _______________________________________________
> >
> >
> > --
> >  PRIVACY WARNING: For auditing purposes, a copy of this message has been
> >  saved in a permanent database.
> >
>
>
>
>
> --
> PRIVACY WARNING: For auditing purposes, a copy of this message has been
> saved in a permanent database.
> _______________________________________________
>
>
>
> --
> PRIVACY WARNING: For auditing purposes, a copy of this message has been
> saved in a permanent database.

--
PRIVACY WARNING: For auditing purposes, a copy of this message has been
saved in a permanent database.